Vertical roller mill
PHOTO


Vertical roller mill is mainly used for grinding raw meal, clinker, Ground Granulated Blast Furnace Slag, iron ore, limestone, coal powder, coke powder, coal gangue, fly ash, volcanic ash, gypsum, calcite, pyrophyllite, quartz, clay, sandstone, bauxite and other processing industry related to metal and non-metal mine.


Features of vertical roller mill


1.High grinding efficiency, advanced grinding principles makes it possible to save as much as 20~30% power consumption when compared with the ball mill. With the increasing of moisture content, it can save more and more electricity.

2.Strong drying capacity: it can make use of the hot waste gases from the kiln to do drying, and it is capable of drying and grinding raw materials with moisture  content as much as 15%.

3.Small in size, and simple process flow: it has integrated crushing, drying, grinding, separating and conveying into one body.
4.Low noises and little dust: there is no direct contact between the grinding rollers and grinding disc. So metallic impact is avoided and its noises is 20~25  decibels lower when compared with ball mill. Totally closed negative pressure operation has employed by this vertical raw mill, so there is no dust during the  operation, which can help to keep the production environment clean.

5.Low wear rate and little metallic pollution: its metal wear is only 5~10g/t.
6.With stable chemical composition and even particle size, its products are quite easy to calcine.


Working principle of vertical roller mill


The motor drives the grinding table to rotate by reducer, and the hot air goes into the inner part of machine at the same time. The materials fall down to the center of grinding table from feed opening. Driven by the centrifugal force, materials move evenly to the edge of the grinding table, and they are grinded by the rollers when going through the rollers’ track. Bulk materials are crushed, while fine materials form material bed after being squeezed and experience intergranular crushing. Grinded materials move on to edge of the grinding table until being taken away by strong airflow at the wind ring, in which larger materials fall to the grinding table by gravity and reground. The others enter the separator being graded. Under the influence of separator blades, materials that do not meet fineness requirements return to the grinding table to be grinded, while the standard ones go into dust collector through the pipes and are discharged as finished products from the discharge device. Irons and other impurities, which cannot be lifted by the wind for weight, move together with materials to the edge of grinding table and fall to the lower cavity, and then they are scraped into the slag discharge opening by stripper plate which is fixed at the bottom of the grinding plate and discharged out of the machine.

vertical roller mill

Figure1.vertical roller mill

1. variable frequency speed of separator; 2. separator; 3. upper shell; 4. main grinding roller device; 5. lower shell; 6. main reducer; 7. base; 8. discharge pipe; 9. feeding port; 10. airproof wind pipe; 11. vice grinding roller device; 12. frame; 13. main motor


Specification of vertical roller mill

4-立磨表格en.jpg

1.High grinding efficiency, advanced grinding principles makes it possible to save as much as 20~30% power consumption when compared with the ball mill. With the increasing of moisture content, it can save more and more electricity.

2.Strong drying capacity: it can make use of the hot waste gases from the kiln to do drying, and it is capable of drying and grinding raw materials with moisture  content as much as 15%.

3.Small in size, and simple process flow: it has integrated crushing, drying, grinding, separating and conveying into one body.
4.Low noises and little dust: there is no direct contact between the grinding rollers and grinding disc. So metallic impact is avoided and its noises is 20~25  decibels lower when compared with ball mill. Totally closed negative pressure operation has employed by this vertical raw mill, so there is no dust during the  operation, which can help to keep the production environment clean.

5.Low wear rate and little metallic pollution: its metal wear is only 5~10g/t.
6.With stable chemical composition and even particle size, its products are quite easy to calcine.


The motor drives the grinding table to rotate by reducer, and the hot air goes into the inner part of machine at the same time. The materials fall down to the center of grinding table from feed opening. Driven by the centrifugal force, materials move evenly to the edge of the grinding table, and they are grinded by the rollers when going through the rollers’ track. Bulk materials are crushed, while fine materials form material bed after being squeezed and experience intergranular crushing. Grinded materials move on to edge of the grinding table until being taken away by strong airflow at the wind ring, in which larger materials fall to the grinding table by gravity and reground. The others enter the separator being graded. Under the influence of separator blades, materials that do not meet fineness requirements return to the grinding table to be grinded, while the standard ones go into dust collector through the pipes and are discharged as finished products from the discharge device. Irons and other impurities, which cannot be lifted by the wind for weight, move together with materials to the edge of grinding table and fall to the lower cavity, and then they are scraped into the slag discharge opening by stripper plate which is fixed at the bottom of the grinding plate and discharged out of the machine.

4-立磨表格en.jpg

your contact information